ESP32-C3 Adblock

日本語 README

A Pi-hole-style DNS ad-blocker that runs on a $2 ESP32-C3 — no PSRAM required.

📰 Featured on Tom's Hardware, XDA Developers, and Korben.

The trick everyone misses: you don't need to keep the blocklist in RAM. Store the domains as sorted 40-bit hashes in flash and binary-search them. 140,000+ domains fit in ~0.7 MB of flash and are matched in ~10 ms, using ~50 KB of RAM.

query in ──▶ extract domain ──▶ FNV-1a hash (+ parent suffixes)
         ──▶ binary-search the flash hash table
              ├─ hit  ──▶ answer 0.0.0.0   (sinkholed)
              └─ miss ──▶ forward to upstream resolver, relay the reply

Why this is interesting

Most ESP32 DNS sinkholes load the blocklist (domain strings) into RAM, so they demand PSRAM. This project stores fixed 5-byte (40-bit) hashes in flash instead:

Why 40 bits? It's the sweet spot for this flash budget. Collisions follow the birthday bound — at 141k domains you get ~0, at 537k about 1 (i.e. one unlucky domain gets over-blocked). Dropping to 32 bits would save 20% of the flash but cost ~7 collisions at 250k; going to 64 bits wastes 3 bytes per domain to solve a problem you don't have.

The same trick works on bigger chips — it isn't a C3 workaround. On a 16 MB ESP32-S3 these hashes hold ~2.7M domains vs ~466k for strings in 8 MB of PSRAM. Hashes in flash beat strings in PSRAM basically everywhere; the C3 just makes it undeniable.

Hardware

• Any ESP32-C3 board (tested on a C3 SuperMini), 4 MB flash, no PSRAM needed
• Classic ESP32 (DevKit / WROOM, 4 MB) also builds: pio run -e esp32dev -t upload (community-contributed, compile-tested; the C3 is the tested target)
• Power it from a stable USB source (a phone charger or your router's USB port). Cheap/loose USB-C→A adapters can brown out the radio during WiFi transmit.
• A USB-A → USB-C dongle lets it plug straight into the spare USB port on the back of most routers — no power supply, no extra box.

Enclosure

A printable case for the C3 SuperMini: hardware/esp32-c3-supermini-enclosure.stl

Printing notes:

• No supports needed; 0.2 mm layers, ~15% infill is plenty.
• Keep the antenna end clear. The C3's PCB antenna is the zig-zag trace on the short edge opposite the USB-C port — don't bury it in solid plastic or put metal near it, or your RSSI will suffer.
• Leave the vents open: the board idles around 45–55 °C.

Build & flash (PlatformIO)

One USB flash to get going — after that, firmware and blocklist both update over WiFi (see below).

⚠️ Use a current PlatformIO — the VSCode PlatformIO extension's bundled core, or pip install -U platformio in a venv. The distro/apt platformio package (e.g. 4.3.4) is too old and fails with AttributeError: ... 'resultcallback' (issue #4). A one-click browser installer is on the way (hosting TBD).

# 1. copy the secrets template (gitignored, stays local) and edit it:
#    - WIFI_SSID / WIFI_PASS are optional — leave the placeholders and use the
#      on-device setup portal instead (below).
#    - WEB_USER / WEB_PASS / OTA_PASS are NOT optional: they gate the dashboard's
#      state-changing endpoints (/ban, /addblock, /upload, /update, /setupdate,
#      /forgetwifi) and network OTA. Pick real values — these used to be wide
#      open to anyone on the LAN.
cp src/secrets.example.h src/secrets.h
#    then edit src/secrets.h

# 2. build the blocklist hash table (default = StevenBlack base + Hagezi Light,
#    ~100k entries, WhatsApp/social safe)
python3 tools/build_blocklist.py data/blocklist.bin

# 3. flash firmware + the blocklist filesystem (the one and only USB flash)
pio run -t upload
pio run -t uploadfs

# 4. watch it boot, note the IP / open the dashboard
pio device monitor          # -> http://c3adblock.local

Your own blocklists

build_blocklist.py OUT.bin [SOURCE ...] takes any mix of URLs and local files, in any of these formats:

• hosts files — 0.0.0.0 ads.example.com tracker.example.com (all domains on the line are included)
• plain domain lists — one domain per line
• AdGuard / Adblock basic rules — ||ads.example.com^ blocks, @@||ok.example.com^ removes a domain (e.g. to mirror an AdGuard Home allowlist)

A blocked domain also blocks its subdomains. Rules a DNS hash list can't express (regex, wildcards, $ modifiers, cosmetic ## rules) are skipped and counted. An @@ rule only un-blocks that exact entry — it can't carve a subdomain out of a blocked parent. If a source can't be downloaded the build stops instead of silently producing a smaller list (--allow-missing to override).

WiFi setup (no re-flash needed)

If it can't connect (or you never set secrets.h), it starts an open access point C3-AdBlock-XXXX with a captive portal — join it from a phone, pick your network, type the password, done. To move it to a new network later: click Forget WiFi on the dashboard, or hold the BOOT button while powering on, and the setup portal comes back. (/forgetwifi requires auth now, so it's no longer a bare URL you can just visit — see Security below.)

Over-the-air updates (no more USB)

The dashboard at http://c3adblock.local does it all:

• Blocklist — drop a freshly built blocklist.bin into Blocklist → Upload, or set a URL under Remote auto-update and the device pulls a prebuilt blocklist.bin on a schedule. A fresh default list is rebuilt every Monday by GitHub Actions and published at a stable URL, so pasting this once keeps a device current on its own: https://github.com/M-Abozaid/esp32-c3-adblock/releases/download/blocklist/blocklist.bin
• Firmware — upload .pio/build/c3/firmware.bin under Firmware → OTA update; the device verifies it and reboots into the new image. Or push over WiFi from the CLI:

  pio run -t upload --upload-port c3adblock.local --upload-protocol espota

4 MB flash tradeoff: firmware OTA needs two app slots, which leaves ~1.3 MB for the blocklist (~250k domains max). The aggressive 537k "ultimate" list only fits the single-app partition table (no firmware OTA). Pick your tradeoff in partitions.csv.

Security

The dashboard's read-only view (/, /stats.json) stays open, but every state-changing endpoint requires HTTP Basic Auth (WEB_USER/WEB_PASS from secrets.h):

• /ban, /addblock, /unblock, /forgetwifi
• /upload, /update (blocklist and firmware OTA)
• /setupdate, /fetchnow

Network OTA (ArduinoOTA, e.g. pio run -t upload --upload-port c3adblock.local --upload-protocol espota) requires OTA_PASS from the same file.

Without this, anyone who could reach the device on the LAN could reflash it with arbitrary firmware or rewrite the blocklist with zero credentials — worth knowing given the device sits in the path of every DNS query on your network. Custom blocked-domain names are also HTML-escaped before being rendered on the dashboard, closing a stored-XSS path where a domain string containing markup (added via /addblock) would otherwise execute in the viewing browser.

Basic Auth here is a LAN-trust-boundary control, not encryption. Everything is plain HTTP on :80 — this chip has no realistic budget to run a TLS server. Basic Auth credentials are base64 (not encrypted) and sent on every authenticated request; anyone who can already sniff your LAN traffic (open/guest WiFi, ARP spoofing) can read them off the wire. This hardens against the common case — another device on your network hitting the API with no credentials at all, or a browser tab CSRF'ing it — not against an on-path network attacker.

CSRF via cached Basic Auth: browsers auto-attach cached Basic Auth credentials to any subsequent request to an already-authenticated origin — including one triggered by a totally unrelated page the same browser visits later (e.g. <img src="http://c3adblock.local/forgetwifi">, no JS required). That would let any webpage silently drive this API once you've logged into the dashboard once, regardless of who's on your LAN. Every mutating endpoint above now also requires a custom X-Requested-With: c3-adblock header, which a plain <img>/auto-submitted <form> CSRF can't attach (only same-origin fetch() can, which is what the dashboard's own JS does) — this is why /forgetwifi is no longer a bare URL you can visit directly; use the dashboard button instead.

Default credentials: if secrets.h still has the placeholder CHANGE_ME_WEB_PASSWORD / CHANGE_ME_OTA_PASSWORD values from secrets.example.h, the device boots with a "password" that's public (it's sitting in this repo's example file). The firmware logs a warning over serial and shows a banner on the dashboard when this is the case — but it will still boot and run, so don't skip setting real values in secrets.h before trusting this on a network you don't fully control.

Out of scope for now: the WiFi setup portal's access point (C3-AdBlock-XXXX) is still open (unencrypted) by design — it needs to be joinable without knowing a password first. The real WiFi password you type into the portal is only as safe as that local radio link during the brief setup window.

Use it

Point a device's DNS at the C3's IP, or add it as a secondary resolver behind your main DNS. Test:

dig @<c3-ip> doubleclick.net   # -> 0.0.0.0  (blocked)
dig @<c3-ip> github.com        # -> real IP  (forwarded)

Gotchas (learned the hard way)

• ModemManager (default on Fedora/Ubuntu) grabs /dev/ttyACM0 and toggles DTR/RTS, which resets the C3 and blocks serial. Fix:

  sudo systemctl stop ModemManager
  echo 'ATTRS{idVendor}=="303a", ENV{ID_MM_DEVICE_IGNORE}="1"' | sudo tee /etc/udev/rules.d/99-esp-no-modemmanager.rules
  sudo udevadm control --reload-rules && sudo udevadm trigger

• The C3's USB-Serial-JTAG console can swallow early boot output until the host connects (while(!Serial) helps).
• DNS clients add an EDNS OPT record; a blocked reply must contain only the question + answer (ANCOUNT=1, NSCOUNT=ARCOUNT=0) or it's malformed.

Done / how it could grow

• ✅ Web dashboard — per-client block/allow counts, ban a client, add custom domains
• ✅ mDNS (c3adblock.local) for discovery
• ✅ OTA — firmware + blocklist update over WiFi, plus scheduled remote blocklist pulls
• ✅ Captive-portal WiFi setup (no hardcoded creds) + one-click browser web-installer
• ⬜ Bucketed prefix index — ~18 flash reads/lookup → ~1–2 (issue #3), the throughput win
• ⬜ Act as the DHCP server (hand itself out as DNS) for true plug-and-play

Credits

Inspired by s60sc/ESP32_AdBlocker — the "answer 0.0.0.0 for blocklisted domains" idea. This is an independent from-scratch implementation focused on the hash-in-flash optimization for PSRAM-less chips.

License

MIT — see LICENSE.